文章详情页-2222

1. The display screen of integrated stove does not light up

Power cord falls off or leakage‑protection plug is damaged. Refer to the wiring diagram, inspect and repair or replace the parts accordingly.
Power board or main control board is damaged. Inspect and judge, then repair or replace.

Power cord falls off or leakage‑protection plug is damaged. Refer to the wiring diagram, inspect and repair or replace the parts accordingly.
Power board or main control board is damaged. Inspect and judge, then repair or replace.
Motor temperature rise exceeds 125 ℃. Normal operation may resume after cooling down. If the motor is burned out, it shall be replaced.
Poor contact of control wire connector. Check the plug according to the circuit connection diagram to ensure reliable contact.
Capacitor is damaged; replace the capacitor.

The ignition knob is not turned by 90°, resulting in small gas outlet and insufficient gas supply for normal combustion. Turn the ignition knob to the correct position as required.
Weak ignition spark: replace the battery.
Blocked gas path. Check whether the gas passage between main gas pipe and branch gas pipe is unobstructed, and inspect if the nozzle is clogged.
The ignition slot of burner cap is misaligned with ignition electrode. Rotate the aluminum burner cap for proper alignment.
Ignition slot of burner cap is clogged; remove blockages from the slot.
Excessive air trapped in gas pipe. Extend ignition duration until air inside the pipe is fully exhausted.
Oxidized ignition electrode; clean it with dry cloth.
Bent or flattened metal hose. Straighten the metal hose and check for gas leakage.

No flame covers thermocouple (ion‑sensing probe); adjust its position.
Abnormal flame at thermocouple position; adjust air damper of inner burner ring.
Damaged pulse igniter or solenoid valve; test and replace the faulty component.

Blocked gas path. Check whether the gas passage between main gas pipe and branch gas pipe is unobstructed, and inspect if the nozzle is clogged.
Poor‑quality gas or residual gas in LPG cylinder; replace the gas source.
Wet burner assembly; let it air‑dry naturally to restore normal state.
Clogged flame ports; clear obstructions in flame ports.
Burner cap and aluminum cap are not seated properly. Fit the burner cap onto positioning pins.
Improper air‑damper adjustment; tune air damper to obtain optimal flame condition.

Poor‑quality gas or residual gas in LPG cylinder; replace the gas source.
Clogged flame ports; clear obstructions in flame ports.
Burner cap and aluminum cap are not seated properly. Fit the burner cap onto positioning pins.
Improper air‑damper adjustment; tune air damper to obtain optimal flame condition.

Power board or main control board is damaged. Inspect and judge, then repair or replace.
Cabinet door is not fully closed or deformed. Close the door tightly or reshape the magnetic sealing gasket.
Damaged door‑control switch; replace the switch.

Incompatible cookware. Use cookware complying with requirements specified in user manual.
Uneven pot bottom; replace with cookware with flat bottom.
Cookware is offset from center. Place cookware at the center of ceramic glass plate.

Abnormal three‑speed fan. Check fan operation and eliminate faults.
Blocked exhaust duct. Keep duct unobstructed without squeezing or collapsing.
Non‑return damper cannot open. Inspect opening status of non‑return damper, adjust or clean it.
Inlet (mesh cover) and outlet of stove chamber are clogged; remove blockages.
Excessively long duct with too many elbows. Shorten duct and reduce the number of elbows.

Power board or main control board is damaged. Inspect and judge, then repair or replace.
Poor connection or crack on metal hose; reconnect firmly or replace the hose.
Gas leakage from valve body; send to service center for repair or replace the valve.
Odor exists in kitchen (e.g. paint odor). Remove odor or strengthen kitchen ventilation.

集成灶常见故障及维修方法